Repair Tips

Why is my roof leaking around the chimney

A chimney leak almost always traces back to failed flashing, not the roof itself. Here is how Duncanville homeowners can spot the cause and get it fixed right.

New step flashing around a brick chimney in Duncanville, Texas

It is almost always the flashing

A chimney is a hole in the roof, and the flashing is what makes that hole watertight: step flashing woven into the shingles on the sides, counter-flashing set into the masonry, and apron flashing on the downhill side. When a chimney leaks, the flashing has usually failed — pulled loose, rusted, cracked at the sealant, or installed without proper step and counter-flashing in the first place. The water runs behind the flashing, rots the decking, and shows up as a stain far from the chimney itself, which is why the stain’s location rarely marks the leak’s source.

Heat is the slow culprit in Duncanville. DFW averages 106 days a year above 90°F, and heat hardens and cracks sealants while wind tugs at flashing edges. Hail dents metal flashing. A flashing system that was sound a decade ago can be the leak today, even though the shingles around it look fine.

Chimney Leaks: Finding the Real Source

  • A stain that grows after rain on the ceiling or wall near the chimney, or on the chimney breast itself.
  • Visible gaps or lifted metal where the flashing meets the brick, visible from the ground with binoculars.
  • Cracked or missing sealant along the counter-flashing line.
  • Dampness in the attic around the chimney, or daylight visible beside the chimney from inside the attic.
  • Efflorescence or spalling brick — white salt staining or flaking brickwork — which suggests water has been moving through the masonry.

Do not just caulk around the chimney and hope. Caulk over a failed flashing is a patch on a symptom: it may hold for one rain and fail in the next, while the decking underneath keeps rotting. The fix is to remove the old flashing, inspect the decking, and install new step and counter-flashing properly.

How the repair works

A proper chimney flashing repair removes the shingles around the chimney, inspects the decking for rot, replaces any soft decking, then installs new step flashing woven into the shingle courses with counter-flashing set into the masonry joints. The shingles are then reinstalled around it. The work should be water-tested before the crew leaves, and you should receive photos of the old flashing, the decking underneath and the new work. If water is coming in now, see our emergency roof repair page for what to do first, and our roof repair page for how a repair is diagnosed. For the ceiling-stain side of the same problem, see why water drips from the ceiling after a storm.

One caution: a chimney leak can also come from the chimney itself — a cracked crown or failed masonry — rather than the flashing. A roofer who only looks at the flashing and never at the crown has not finished the diagnosis. To arrange an inspection that checks both, call (469) 898-7253.

Tagged with

#chimney leak#roof flashing#duncanville#roof repair#water damage
FAQ

Frequently Asked Questions

Why is my roof leaking around the chimney in Duncanville TX?
Almost always a flashing failure: step or counter-flashing pulled loose, rusted or badly installed, or sealant cracked by heat. Water runs behind the flashing and rots the decking, showing up as a stain far from the chimney.
How do I fix a chimney leak in Duncanville Texas?
Remove the old flashing, inspect the decking for rot, replace soft decking, and install new step and counter-flashing woven into the shingles. Caulk alone is a patch on the symptom, not a fix.
Does chimney flashing cause roof leaks in Duncanville TX?
Yes — flashing and penetration failures are among the most common leak sources on an otherwise sound roof, because heat cracks sealant and wind works flashing loose over time.
Who repairs chimney leaks in Duncanville Texas?
A roofing contractor repairs the flashing and decking. If the leak comes from the chimney crown or masonry rather than the flashing, that part is masonry work — a roofer should say so rather than flashing over it.
Can I just caulk around my chimney to stop the leak?
No. Caulk over failed flashing may hold for one rain and fail in the next, while the decking underneath keeps rotting. The flashing itself needs to be removed, inspected and replaced.

Get your chimney leak fixed by a Duncanville roofing team that finds the real source

Call Cabrera & Sons Roofing to arrange a chimney leak inspection. We inspect the flashing, crown and attic to pinpoint the leak, then repair it so it stays fixed.